Fxo jobs
I have a server with an FXO card, the scenario that i need to do it is this: 1.- i have extension 100 with a mobile phone in a follow me destination 2.- if the mobile phone it is not picked up in 9 or 10 seconds needs to send to voicemail or IVR or another destination (like a ring group) the main problem is that i cannot make the asterisk to understand when the PSTN call exceeds that ring time because for asterisk the call it is answered so i need a help to setup correctly my box for make it to work please only experienced freepbx / asterisk users needed
I am currently facing an issue with my Issabel PBX setup connected to a D-Link DVG-6004S FXO Gateway. While I'm able to make outgoing calls successfully, I cannot receive incoming calls. Requirements: 1- Proficiency with Issabel PBX and D-Link FXO Gateways. 2- Ability to quickly diagnose and resolve the issue. 3- Availability to work on this immediately and resolve within 50 minutes. 4- Strong communication skills in English. If you believe you're the right fit, please contact me ASAP. Compensation will be provided for the quick and successful resolution of this issue.
I have 8 FXO and only accessiable via SIP. They are BT1, BT2, BT3, BT4, BT5, BT6, BT7 and BT8 I need asterisk to check for call counter before making a call. Only least / lowest number of the BT port counter can be dial out. Below is my logic. Everytime when asterisk receive a dial request 1. asterisk will check which BTs has the least number of call 2. once known, asterisk will dial the call. for example BT1 3. Regradless of the status of call, (ANSWERED, BUSY. UNAVAILABLE), asterisk will add BT1+1 The idea is to evenly distribute the call between all FXOs. You will need to have anydesk and access to my PC to work as asterisk is only available locally. (LAN)
Need help in inbound and outbound etc .
Hi, I’m looking for a price for someone to take my .FXO files (room design created in articad) and create a higher quality renders with better lighting and background. I’m looking for the quality to be as good as the header on the Howdens Kitchens main page. Preferably with the same movable effect.
it is required to connect Issabel Voip server with Yeastar FXO 410 and configure a call center system
Hi, We need assistance to set up Elastix last version 5 1. 7 internal extensions 2. 4 fxo ports with analog lines (sangoma a400 card) 3. Dedicated outgoing calls from extension through the correct fxo port 4. Incoming call to dedicated extension on chosen fxo. 5. Fax to email Reach me by whatsappp 198o322872two
Hi everyone, Please don't waste my time, if you've done it over and over again and the process doesn't take more than 15 minutes then make your offer.
Hi I noticed your profile and would like to offer you my project. Require custom PBX software built on Asterisk platform including GUI. It will be limited to number of users/phones and license to be uploaded/entered for upgradation of users/phones - IVRS and log - Phone Logo change - Live Monitoring and real time status - Video Conferencing - FXO/FXS/PRI/Trunk Gateway Integration & support - License based features to limit number of users/phones is a must
Hi Eremin P., I noticed your profile and would like to offer you my project. Require custom PBX software built on Asterisk platform including GUI. It will be limited to number of users/phones and license to be uploaded/entered for upgradation of users/phones - IVRS and log - Phone Logo change - Live Monitoring and real time status - Video Conferencing - FXO/FXS/PRI/Trunk Gateway Integration & support - License based features to limit number of users/phones is a must
...on server/hardware. It will be limited to number of users/phones and license to be uploaded/entered for upgradation of users/phones. GUI will have company branding. PBX software shall be inclusive of below modules but not limited to these only. - Detailed CDR - Call Recording - IVRS and log - Phone Logo change - Live Monitoring and real time status - Softphones integration - Video Conferencing - FXO/FXS/PRI/Trunk Gateway Integration & support - License based features to limit number of users/phones - Free Modules of freepbx/Pbxact - Built-in Redundancy Developer need to provide 6 Months support in this project from developer for testing/bugs/reports/problem of any kind. Future upgradation shall be possible on the software and same person will be assigned for this, however it...
Configuration of DVG600s to send calls, and configure cloudfonica pbx to send calls to the gateway the gateway will send the call to PSTN. only 1 channel FXO. Please consider this requeriments: Cloudfonica PBX should send SIP Invite packets to Dlink Gateway. If FXO lines form PSTN are not working, calls can not go through.
i need to configure D-Link DVG-6004S fxo to be able to dial out calls received from sip through pstn lines
Hello, i offer 10% commission for each sale, i have for sale Mediant 800 with FXS, FXO, BRI, SBC, OSN Mediant 1000B with FXS, FXO, BRI, SBC, OSN Mediant 2000 with 4/8/16E1 T1, SS7 Mediant 3000 TP8410 with SS7, SBC Mediant 3000 with TP6310 with SS7, SBC Mediant 2600/4000/ 4000B with SBC Mediant 5000/8000
We are suffering intermittent quality issue, 3cx Is connected to GSM gateway and FXO gateway in A Microtik environment. If you are confident to solve it, you are welcome to bid. Payment will be processed only 7 days after successful completion ONLY. No partial payment if u failed to solve the problem.
We have an Issabel IP PBX working with 3 gateway ATA Grandstream HT 503 with 1 FXO each one. We need to replace those ATA with a new gateway Dinstar with 4 FXO on same hardware. Only 3 FXO must be configured to register on Issabel.
Dear all, I have CISCO router act as a FXO gateway for Asterisk server, it was working find upto the point where the incoming calls are not being ended when hangup , it keep active which make the line always busy,
Dear all, I am seeking someone who is an expert in FreePBX and CISCO routers as its used as FXO I have managed to configure both and all is good except for the follow me , keep getting issues
Dear all, I am seeking someone who is an expert in FreePBX and CISCO routers as its used as FXO I have managed to configure both and all is good except for the follow me , keep getting issues
Dear all, I am seeking someone who is an expert in FreePBX and CISCO routers as its used as FXO I have managed to configure both and all is good except for the follow me , keep getting issues
We have a ISR4331 that we use as a voice gateway. Currently it is on version isr4300-universalk9.03.16.04b.S.155-3.S4b-ext.SPA.bin. The TCL script send a tone to an FXO port at certain times that we use as a shift-bell. I would like to upgrade to but when I do the TCL does not function. Because this is a production system we need to troubleshoot during non-business times. After the upgrade, it doesn't even initialize the call I ran a kron debug and found: with : 000178: Dec 28 12:23:38.577: %SYS-5-CONFIG_I: Configured from console by onyx on vty0 () 000179: Dec 28 06:25:00.001: Major 1, Minor 0 000180: Dec 28 06:25:00.001: Timer Event ShiftChange10 000181: Dec 28 06:25:00.001: Kron delay for next ShiftChange10
We're converting from POTS to T1 I'm looking for someone that's done this before and can walk me through it. Applicant should be an expert at Cisco CUCM and voice gateways.
We're converting from POTS to T1 I'm looking for someone that's done this before and can walk me through it. Applicant should be an expert at Cisco CUCM and voice gateways.
install gui configure wan internet port 2 vlan- phone - pc pc connection from phone 2 fxo group call forward call contact list fxo0 hunting group all 201,202,203,204 at same time fxo1 hunting group all 301, 302, at same time extension: 200 201 202 203 204 301 302 calls out from 200 to 204 to fxo1 call out from 301 to 302 to fxo2 pattern output call to pstn - 9 digit direct to pstn - 10 digit starting with 6 direct to pstn
2 offices located 1 hour away from each other. Raspberry Pi4 with 3cx PBX at “main” location “Main” location has fiber optic internet 200/60 down/up speed, other location cable 150/50 down/up Public IP but not static Each location has Gateway VOIP Grandstream 4 Fxo GXW-4104 Each location has 2 landlines and 1 SIP/VOIP line Various phones to connect, most are Grandstream GXV3240, 3370 and 3275 No operator per se, small business where whoever is available takes calls Both locations have battery backup on equipment I want to connect all lines from both locations so people at 2 offices can call out, answer, intercom between phones. Ability to take a phone home and be connected to office for the casual employees or for covid lockdown. Make sure phones are pro...
We're converting from fxo to pri. I'm looking for someone that's done this before and can walk me through it. Applicant should be an expert at Cisco CUCM
We us e a Grandstream with FXO /FXS port that connects to a termination device. We send calls from the internet to this device however calls are being billed from the point the ATA device rings the termination device rather than when the call is answered. What need is the ATA device correctly configured
I need to make Voice over IP calls between 2 countries, to landlines and mobile numbers: In both countries I ALREADY have "landline" service (PSTN) with unlimited call plans. I would prefer NOT To use an Asterix, Elastix or similar solution, in that case I rather to use a low cost solution such as the old Linksys SPA3102 or similar device (with FXS, FXO ports) I know that there are “virtual PBX” services with low costs BUT if I already pay for unlimited calls service, and I DO NOT want to pay additional monthly costs or additional costs per call. So, What What I need ? : I need an explicit diagram of a low cost solution using my current PSTN lines . Preferably be based on ATA-type devices like the Linksys SPA 3102 or something similar cost solutions,...
Need some asstiance getting SIP Trunks setup between Grandstreem UCM6204 and Flowroute SIP Trunk Provider. New UCM and flowroute setup. UCM is functional and able to make calls using FXO. 1. System is registering with Flowroute 2. Assitance with Inbound and Outbound Routes 3. DID routing
Install and configure and integrate with GSM gateway and FXO Gateway on cloud and On prmsis and bridge them. Create Ext,IVR, Quw similar to existing 3cx . STABLE SNG7-PBX-64bit-2002 Release Date: February 2020 FreePBX 15 • Linux 7.6 • Asterisk 13 or 16 Supports UEFI and Legacy BIOS booting
Hello, I'm looking for someone who can setup my 4FXO to make outgoing calls only, from an external SIP software (SIP registration from another IP connection, no local uses). 3 telecom providers will be connected to this VoIP ATA. The device has been bought to ChinaSkyline, it looks like this : (but with 4 FXO ports). I give you a TV code for your work. Thank you for you consideration ! Best regards
Due to hardware problems our very old ...linked equipment so we made do using a direct line, our mobiles and a professional skype account. However we would like to get the situation fixed before the end of the year if possible. Due to the situation the Asterisk will need to be set up on a fairly new server (2x XEON E5-2620v3 6 Core 2.4GHz/32GB(2x16GB)) but with some old(er) peripherals like a DrayTec Vigor 3300V switch which holds the FXO and FXS connections, some grandstream SIP phones and a few regular PSTN phones, as well as Softphones on our laptops and Android phones. Also there is a SIP door intercom we would like to get working again ... We would set up the (Linux) server to specifications we agree upon and the installation of Asterisk and it's configuration would be y...
Unable to play music file in FreePBX error "Unable to find an intermediary converter for /home/asterisk" And FXO Tele Routing & FreePBX Inbound Configuration need to be setup
I need someone to help configure the Patton SmartNode 4114 (FXO Port) with Freepbx/Asterisk so we can use SmartNode 4114 as a VoIP gateway for PSTN lines.
hello. I need to build an electronic card that can be used with Raspberry Pi 2&3. the card will have the features bellow: - 1 (one) Port FXS. - 1 (one) Port FXO. Also to make it works we need the drivers to be installed on the RSPi and of course those drivers must be well known to get things works easily. great luck
I need some one to setup Multiple Telephone systems consisting of FreePBX , a Fxo Gateway Grandstream GS-GXW4108 , and multiple Voip Phones. You must have full knowledge and experience in FreePBX, asterisk and networking setup and must be able to continues support based on a monthly fee.
Hello Freelancers, I have a Dinstar 4 Port FXO Gateway with FreePBX installed on my Raspberry Pi in my office. I need you to reconfigure the FreePBX for both inbound and outbound routes. I will only pay if the configuration works and there is no problem.
we have connected panasonic pbx tes824 to grandstream ucm 6204 Panasonic FXS port / extension 18 , 19 , 25 connected to UCM FXO 1,2,3 respectively Calls from Panasonic and UCM is working fine , But calls coming from Panasonic extension to fxo port cannot detect caller id and over ip phone it shows caller id undetected.
We have inegrated panasonic tes824 pabx with ucm 6204, Panasonic FXS port / extension 18 , 19 , 25 connected to UCM FXO 1,2,3 respectively Calls from Panasonic and UCM is working fine , But calls coming from Panasonic extension to fxo port cannot detect caller id and over ip phone it shows caller id undetected. Please support
I have a customer with a Cisco UC560-FXO-K9 Phone System which has reached end-of-service life a few years ago. It is having problems, and we need to keep it limping along long enough to get them a replacement solution. I am looking for someone or company that is knowledgeable enough to help us do that for a fee or time &materials. It is in the Chicagoland area.
1- Create a Cloud Server on Digital Ocean or any alternative , using our account . 2- Install 3CX Pbx on it . 3- Connect Fortinet 61e Firewall or dreytek firewall between office and Cloud Server . . ADSL internet configuration • Dyndns configuration • VPN configuration to Cloud DC • Policy configur...Install 3CX Pbx on it . 3- Connect Fortinet 61e Firewall or dreytek firewall between office and Cloud Server . . ADSL internet configuration • Dyndns configuration • VPN configuration to Cloud DC • Policy configuration to allow internet and VPN traffic • Security profile configuration IPS, AV and DNS filter • Web filter and application control configuration as per best practices 4- Configure GSM/FXO gateway to server ( Bero Net or yeaster s20 )...
1- Create a Cloud Server on Digital Ocean , using our account . 2- Install 3CX Pbx on it . 3- Connect Fortinet 61e Firewall or dreytek firewall between office and Cloud Server . . ADSL internet configuration • Dyndns configuration • VPN configuration to Cloud DC • Policy configuration to allow inte...Install 3CX Pbx on it . 3- Connect Fortinet 61e Firewall or dreytek firewall between office and Cloud Server . . ADSL internet configuration • Dyndns configuration • VPN configuration to Cloud DC • Policy configuration to allow internet and VPN traffic • Security profile configuration IPS, AV and DNS filter • Web filter and application control configuration as per best practices 4- Configure GSM/FXO gateway to server ( Bero Net or yeaster s20 )...
Hi, I need someone who did the configuration of D-Link dvg6004s FXO Gateway with Elastix 2.4 many times To do the job to me.
i need someone to create and IVR for me using Asterisk that will interact with mysql database for callers details and readout details form database using TTS (Hindi and English) there should be option to call http apis and also the call flow should be easy to modify i have previously done it using PHP api but never got time to finish this (i don't have the codes now) there are 3 le...interact with mysql database for callers details and readout details form database using TTS (Hindi and English) there should be option to call http apis and also the call flow should be easy to modify i have previously done it using PHP api but never got time to finish this (i don't have the codes now) there are 3 levels of menu and it must use 3G datacards to receive make calls not ju...
Hi We are looking for freelancer who is aware of complete integration and workflow of GrandStream HT813 with Issabel. Issues to resolve Call Progress Dial Tones to be set for Airtel (India) Call disconnection (FXO Termination) to be set Other settings Secure Connection between device and server Complete Trunk related settings in Grand Stream and Issabel (Elastix) Only bid if you have complete know how to resolve the issue Connection will be done by RDP
please offer you the best-discounted price for the Installation & Configuration of the following BOQ. S/N Part Number Description Qty 1 R-UCL-UCM-LIC-K9 Top Level SKU For 9.x/10.x User License eDelivery 1 2 CON-ECMU-RUCLUCK9 SWSS UPGRADES Top Level SKU For 9 1 3 CUCM-VERS-11.5 CUCM Software version 11.5 1 4 LIC-CUCM-11X-BAS-A UC Man...4400 ISR 1 23 SRST-EP Cisco SRST- SRST Endpoint License (E-Delivery Smart) 9 24 CON-ECMU-SRSTGTEP SWSS UPGRADES Cisco SRST-1 SRST Endpoint License 9 25 CUE-IVR Cisco Unity Express v9.x- IVR Session (E-Delivery Smart) 2 26 CON-ECMU-CUEIVRTB SWSS UPGRADES Cisco Unity Express (CUE) IVR Licens 2 27 SISR4300UK9-316S Cisco ISR 4300 Series IOS XE Universal 1 28 NIM-4FXO 4-port Network Interface Module FXO (Universal) 1 Your prompt response will be highl...
I have an Asterisk server for private use already running, and would like to acidify a Trunk using an FXO VoIP Gateway, for this is necessary to create a sip trunk in Asterisk and I do not know how to do. In my attempts, I can even connect SIP between them, but I can not complete calls.
