Arduino Jobs

I’m putting together a compact two–tier electronic enclosure and I need the complete assembly modelled in Shapr3D so I can open, review, and tweak the layout myself. Here’s the flow of work: • You’ll source accurate 3 D models for several off-the-shelf parts plus one OEM component. I already have its detailed specs in PDF, which I’ll forward immediately. • Once the parts are ready, you’ll position them inside a base housing roughly 10 in × 9 in × 2.5 in, then add a second enclosure that stacks neatly on top. • Please illustrate the electrical and fluid links: a triple-lumen 1⁄16″ ID umbilical running between the tiers, and wiring that ties a water-level sensor, a peristaltic pump, and an Arduino-class controlle...

I am looking for someone to develop hardware on my request, it will be simple projects as seen on you tube. I am interested to know hourly rates, if I provide the hardware and code they would just need to wire them up. Would be nice to have someone from India NCR.

The task is to design a compact PCB that drops straight into an SCX 1/32 car so it can run on a digital track. I want the board to read the track’s reed-sensor signal, let me assign any of 20 unique car IDs in firmware, and expose a surface-mount USB-C port on the edge for easy flashing once the body shell is back on. Size must stay close to the original analogue board footprint (about 24 × 18 mm, height under 6 mm) but I can adapt mounting holes or connector positions if you have a cleaner layout idea. Power comes from the standard track pickups (nominal 14–18 V DC), so include an efficient buck or LDO to feed the microcontroller and reed circuitry. I haven’t locked the MCU yet; pick anything small, inexpensive, and easy to program—ATmega, STM32, ESP32, or s...

Multi-Arduino Industrial Control System Development (Isolated Communication + Analog + Digital I/O) Project Overview We are developing a modular measurement instrument based on multiple interconnected Arduino boards. Each Arduino handles a dedicated subsystem (UI, motor control, pH control, temperature control) coordinated by a Master Arduino. We require an experienced embedded systems freelancer to: • Design robust firmware architecture • Implement reliable inter-Arduino communication • Ensure electrical isolation to prevent analog noise/crosstalk • Optimize motor control, sensor acquisition, and closed-loop control • Deliver clean, documented, production-ready code • All components should be easily sourced in India This is not a beginner Arduino project &md...

I need a concise Python 3 script that will run on a Raspberry Pi 5 and do the following: • Watch a single GPIO input line for the HIGH digital signal coming from my Sony camera’s built-in AI output. • As soon as that digital signal is detected, drive a separate GPIO output that energises a small 5 V solenoid for five seconds, then automatically switch it off. • Debounce or otherwise ignore any further triggers until the five-second period is complete. The camera only provides a digital signal, so no protocol parsing is required—plain HIGH/LOW logic on the GPIO pin is all I need. The trigger itself must use the Pi’s native GPIO header rather than USB or networking. I haven’t fixed the exact GPIO numbers yet; feel free to suggest sensible default...

Project: ESP32-Based Talking Plush Toy – Prototype Development Project Overview I’m building a screen-free talking plush toy for kids (3–7 years). The goal is to create a working prototype (V1) that demonstrates: Calm audio interaction Simple button & Bluetooth (BLE) control Safe, battery-powered operation This is prototype-only, not mass production. Scope of Work The freelancer will: Build a working ESP32-based prototype Implement audio playback (pre-recorded voice files) Support button-based triggers Implement BLE connectivity (basic commands from phone) Ensure safe power & insulation for a prototype Share code + wiring diagram + build instructions Core Features (V1) ESP32 dev board Pre-recorded audio playback (stories, phrases) 1–2 physical buttons BLE co...

I need an ebike throttle limiter that sits between the ebike throttle ( running 5v red, black (gnd) and white control wire and its controller : (DO NOT CUT these) Throttle RED (+5V) ------------------------------------ Controller RED (+5V) Throttle BLACK (GND) ------------------------------------ Controller BLACK (GND) (ONLY cut/switch the WHITE signal) Throttle WHITE (signal) ----+-----------------------------> Switch T1 | +----[ Rseries 1kΩ ]----+-----> Switch T2 = LIMIT NODE | +-----> Pot BLACK (wiper) Pot RED ---------------------------------------------> Controller...

I'm seeking an experienced PLC programmer to convert my existing SLC500 process control system to a Click PLC. The SLC500 is obsolete, and I need to ensure continuity in process control with a modern solution. Key Requirements: - Migrate all existing code and logic from SLC500 to Click PLC. - Ensure that the Click PLC can replicate all current process control functionalities. Ideal Skills and Experience: - Proficiency in both SLC500 and Click PLC systems. - Strong background in process control automation. - Experience with PLC programming and code migration. - Attention to detail to ensure no loss of functionality during the transition. Please provide examples of similar work done and ensure you have the necessary skills to handle this migration seamlessly.

I need help building a working prototype of a small interactive toy. The prototype requires: A pop-up mechanism (using solenoids, springs, and/or small motors). Integration with Raspberry Pi or Arduino for control. Wiring/programming to operate the mechanism. A simple phone/web app to trigger the toy remotely. Requirements: Experience with mechanical design and prototyping. Hands-on skills with Raspberry Pi/Arduino electronics. Must show past project work (photos, CAD, or GitHub). Signed NDA. Deliverable: A working physical prototype (not just design files) that demonstrates the pop-up mechanism controlled by Raspberry Pi/Arduino. Budget: Budget will be discussed based on scope and experience. Please provide: What’s your estimated cost? How did you arrive at that numbe...

I want the running total revenue from my Shopify store to show on a Wi-Fi-enabled physical counter that sits on my desk. The job is to build the small bridge between Shopify’s JSON API and the hardware. Here’s what I already have and what I need from you: • Data source – Shopify: I only care about the store’s Total revenue figure. A lightweight call to the REST Admin API (or GraphQL if you prefer) is enough. I will supply the private-app credentials. • Destination – Hardware counter: It connects over Wi-Fi. You can target it with plain HTTP, WebSocket, or MQTT; whichever is simplest to flash onto a common ESP8266/ESP32 controller. I can handle the flashing if you give me the compiled binary or the Arduino/PlatformIO project. • Service layer:...

We are a hotel using a specific electronic door lock. We need to integrate these locks with our Property Management System (PMS) to automate keycard management. The lock company cannot provide an API or documentation, so we need to determine the communication protocol and build a custom interface. Scope of Work: Analyze the communication protocol between the lock system and its hardware. Develop a software middleware/API to connect our PMS to the lock system. The interface must handle core functions: creating new keycards for check-in, extending access, and revoking access at check-out. Provide clear documentation on the protocol and the solution. Test the integration to ensure it is reliable. Dumps of Master Card, Guest Cards, Configuration Cards and Add Locks Card will be provided. Th...

I have an air-quality monitor prototype on breadboard and now need a production-ready PCB. The core of the board will be an Arduino Nano, linked to Wi-Fi for cloud logging and OTA updates. Only a particulate-matter sensor has to be integrated at this stage, but I’d like the layout to leave space and headers so a future gas sensor can be dropped in without a full redesign. What I expect from you: • Complete schematic, PCB layout and clean routing for the Nano, Wi-Fi module, particulate sensor, regulated power path (USB-5 V input and Li-ion option), plus an on-board antenna or footprint. • Clearly labelled break-outs for I²C, UART and an SPI port, and pads for an optional 0.96" OLED or similar display. • All design files (KiCad or Altium), Gerbers, dr...

I’m putting together a compact desk ornament that spins on command, and I need a complete PCB solution to drive the rotation reliably. The ornament will only move when a small switch is flipped—no sensors, no remotes, just simple manual control feeding a quiet motor. Main Features: • main power source is 5V from USB to DC power jack connected to board via JST-PH cable 2pin socket. • 3.7V 800mAH Lithium chargeable battery as backup power source, connected via JST-XH cable. • 3-way SPDT switch(on, off, timer) connected to the PCB via a JST-XH cable. • 3V DC motor with peak current around 3A, connected to board via JST-PH(2pin) • 2 mounting points (M3 size to allow M2.5 bolts) Here’s what I’m after: • Schematic and PCB layout for a ...

Hello , I need a complete design for a compact consumer-electronics board that revolves around a PIC microcontroller. The scope spans three tightly-linked parts: • PCB hardware – Produce the schematic and multilayer layout in Altium Designer, include all libraries you create, and deliver the full manufacturing package (Gerbers, drill files, pick-and-place, and a PDF schematic). • MCU firmware – Write well-commented code in MikroBasic (or another PIC-friendly tool if you justify the switch). The firmware must read multiple sensors, exchange data through an efficient serial protocol, and use smart power-saving modes to stretch battery life. Please supply project files, compiled HEX, and a short flashing guide. • PC interface – Build a Windows utility in VB....

I need a complete design for a compact consumer-electronics board that revolves around a PIC microcontroller. The scope spans three tightly-linked parts: • PCB hardware – Produce the schematic and multilayer layout in Altium Designer, include all libraries you create, and deliver the full manufacturing package (Gerbers, drill files, pick-and-place, and a PDF schematic). • MCU firmware – Write well-commented code in MikroBasic (or another PIC-friendly tool if you justify the switch). The firmware must read multiple sensors, exchange data through an efficient serial protocol, and use smart power-saving modes to stretch battery life. Please supply project files, compiled HEX, and a short flashing guide. • PC interface – Build a Windows utility in VB.NET ...

Overview I’m looking to develop a robust UART to UDP bridge on STM32 for handling large binary frames and NMEA data. The aim is to enhance data transmission reliability between devices. Scope of work - Develop a UART RX system with DMA and ring buffer on STM32 for lossless data reception. - Implement UDP TX using LWIP for sending data over UDP with configurable IP and port. - Handle large frames by sending in single datagram or using fragmentation protocol (frame_id, chunk_index, total_chunks, crc) for payloads around 10KB. - Optional: forward NMEA data on a separate UDP port. - Deliver complete CubeIDE project and documentation. - Test and verify UDP reception with log/pcap/wireshark or video to prove valid frame transmission. Additional information I’ll accept delivery a...

I already have a working PCB built around an Xsens MTi-630 IMU and an NXP MKV56 microcontroller. What I need now is a technician who can revise the existing firmware so the remote camera head delivers rock-solid motion compensation on set. Your task is to design and embed a custom sensor-fusion routine that blends gyro, accelerometer, and magnetometer data from the MTi-630, then feed that fused orientation into the motor-control loop over CANopen. I’m aiming for a balanced mix of speed and accuracy so operators never feel lag yet still enjoy drift-free performance during long takes. You will be starting from my current codebase (MCUXpresso / NXP SDK), which already handles basic hardware abstraction and CANopen messaging. The focus is on: • Writing or adapting a quaterni...

I'm looking for a simple laser tag prototype using ESP32 and IR technology. This is for concept testing, not a final product. Essential features: - Scorekeeping - Player detection - Team identification Additional feedback mechanisms would be a plus but are not mandatory. Ideal skills and experience: - Experience with ESP32 and IR communication - Background in game mechanics for scorekeeping and player detection - Ability to develop a user-friendly prototype Please provide samples of similar work. Also looking for someone working out of India so that I can get my hands on the final prototype, no matter how simple it is.

The goal is straightforward: as soon as an ESP device is present—whether connected over Wi-Fi or broadcasting in monitor mode could be spotted in hidden places

ATLANTIS OTA UPDATE SYSTEM – DEV PROMPT (WIFI TEST FIRMWARE) Objective Implement a production-grade OTA firmware update system for Atlantis controllers that is safe, rollback-capable, power-loss tolerant, and integrates with Blynk NCP (ESP32 runs unmodified NCP firmware). Deliver test firmware that validates the entire OTA lifecycle over Wi-Fi before Blynk integration. System Overview Hardware Primary MCU: STM32H723VIT6 (main firmware; Arduino sketch runtime) Connectivity MCU: ESP32 running Blynk NCP binary (not modifiable) Dealer flashing: Android Dealer Toolkit via USB-C UART, toggling BOOT0 + NRST, using STM32 ROM bootloader Dealer flashing is force-install / recovery Dealer flashing does NOT interact with running firmware Dealer flashing does NOT write OTA metadata Non-Negotiabl...

I want to turn my stock WowWee MiP into a fully-independent companion with far more capability than the original phone-controlled toy. The big push is to give it functional robotic arms—servo-driven, proportional, and strong enough to perform simple pick-and-place demos—while keeping the self-balancing chassis intact. To drive everything, I need an internal “brain” (Raspberry Pi, ESP32, or another MCU you’re comfortable with) that can: • run onboard code without any phone connection • store multiple programs in flash so I can swap behaviors on the fly • process a forward-facing camera for navigation and object tracking • handle voice-command triggers and speak back in character using a small speaker For interaction I’m l...

I have a production-ready, IGBT full-bridge welding inverter that already powers both TIG and MMA processes, yet the embedded side still needs a final expert pass before release. The control board is built around 8051 and STC MCUs running Keil C51 firmware, and every line of code directly shapes arc stability, HF start, AC balance, soft-start, and safety interlocks. The short-term goal: review, tidy, and extend the existing code so it drives the power stage flawlessly in TIG and MMA, AC and DC. That means refining PWM timing, gate-drive dead-time, current-feedback filtering, and all the little state-machine details that separate a decent welder from a great one. Core tasks and deliverables • Audit the present C51 codebase, flagging race conditions or timing pitfalls. • Im...

Need tutor for the group design project Tool and everything mentioned in the Pdf file i will need professional academic tutor who can handle project perfectly project will have weekly updates + full final report which have simulation MATLAB or Arduino After this project will have more projects incoming so plz come with sample work also You all can bid i will reply and will check the sample work and will select who has good sample work and quality Tutor must be active who can reply faster for students answers Check pdf for more information Thanks Dr. Khan

I need help setting up two Nema 17 stepper motors to be controlled remotely via two ESP32 boards. One board will be in the remote and the other in the receiver. Requirements: - Manual control of stepper motors - Input commands using an analog joystick Ideal Skills and Experience: - Experience with ESP32 and stepper motors - Familiarity with joystick integration - Strong knowledge of manual control systems Please provide a detailed plan and relevant experience in your bid.

I need a clean, production-ready PlatformIO project for the Nordic nRF51822 written in C/C++. The example must boot, scan for nearby BLE devices, connect to one of them, and exchange plain text strings—ideally via a Nordic UART–style GATT service. Please build it around a SoftDevice or Nordic SDK you have already proven on real hardware; I do not want AI-generated scaffolding that compiles but fails at runtime. The code should: • compile inside PlatformIO with a single pio run command • flash successfully to an nRF51822 DK or compatible module • start scanning, connect on the first match, and perform a two-way text message exchange • cleanly disconnect and resume scanning Deliverables I’ll review: 1. A complete PlatformIO project folder (ma...

I aim to develop a solution that will facilitate data communication between an Arduino UNO and a SIM7600E using AT+COMMAND. The primary data in focus will be temperature sensor readings. Key Responsibilities: - Setting up a reliable connection between Arduino UNO and SIM7600E - Implement AT+COMMAND for effective communication - Design a protocol for transmitting temperature sensor data Ideal Skills: - Solid knowledge of Arduino - Proficiency in handling SIM7600E - Experience in implementing AT+COMMAND - Understanding of sensor data transmissions. Please ensure you can efficiently deliver on these requirements, and provide the mentioned sensor data communication before placing your bid.

我想用一块 ESP32 搭配 INMP441 数字麦克风和 MAX98357A 扩音模组，做一个能“听得懂、说得出”的小型语音 AI。场景非常基础：与人进行简短对话，并可通过语音指令开关雾化模块即可，不需要复杂的物联网整合。 核心功能 • 语音识别：本地或云端均可，只要稳定； • 语音合成：中文语音播放，音质无需高保真； • 故障检测：当雾化模块或语音链路异常时给出语音或串口提示。 期望成果 1. 可直接烧录到 ESP32 的完整源码（Arduino IDE 或 ESP-IDF 均可）。 2. INMP441、MAX98357A、雾化模块的接线图与电源注意事项。 3. 简易指令表（如“开始雾化 / 停止雾化 / 查询状态”）及触发话术。 4. 编译、烧录与测试步骤说明，确保我按步骤即可复现。 若你能提供额外的调音参数、噪声抑制建议或 OTA 升级预留接口，我也非常欢迎。

Saya ingin 10 artikel bertema elektronika yang ringan dibaca namun tetap akurat. Total pembagiannya: • 3 artikel Robotik (contoh: cara membuat robot line-tracer sederhana) • 3 artikel Sirkuit Dasar (penjelasan komponen, rangkaian power supply, dsb.) • 4 artikel Tips dan Trik Elektronik (troubleshooting, efisiensi, safety) Setiap artikel harus: • Minimal 700 kata dengan gaya informal dan mudah dimengerti. • Menyertakan setidaknya 1 ilustrasi relevan (foto, diagram, atau skema). • Diberi judul menarik, sub-header jelas, dan penutup ringkas. Setelah seluruh konten siap, satukan ke dalam satu file PDF berisi kesepuluh artikel, urut sesuai daftar di atas. Proyek dinyatakan selesai begitu saya menerima PDF final lengkap. Saya terbuka pada ide contoh ...

I'd like to create a schematic and PCB layout that I can use to print from a photo I have. The layout is based on an ATmega and an ESP32, along with a servo connected to the ATmega. I'd like a guide on how to create a schematic file that I can modify and use in the future, not just the photos I have.