PCB Layout Jobs

1) Need to do total re routing 2) need to add esp32 c6 wroom 1 vis uart,spi and i2c 3) add eeprom 4) correct modbus error 5) re naming all I/O

Need small anf compact HDI multilayer pcb from systematic to pcba which can be connected with my existing smartphone pcb . Requirement in custom pcb are - 1) NFC + custom NFC antena 2) Secure element 3) secure MCU 4) type C USB for data 5) vibrator 6) touch buttons 7) pogo pins for charging BOM and all details of my main pcb will be discussed and provided to you

I already have a complete schematic and BOM for an embedded-system board and now need someone to turn it into a production-ready PCB in KiCad. You will receive the schematic, component list, and the exact board outline with mounting-hole locations so the size constraint is fixed from the start. Your task is to place all parts logically for signal integrity and serviceability, route power and ground planes cleanly, add connectors exactly where the enclosure dictates, and run full DRC to be certain the board will pass fabrication checks the first time. Please keep an eye on trace widths, clearances, and manufacturability rules that mainstream fabs expect. When finished, send me: • The complete KiCad project (schematic symbols, footprints, and PCB layout) • Gerber and drill fil...

I need a complete electronics solution that can replace the original EBB board on an Axidraw-style writing machine. The job covers both hardware and software. Hardware scope • Design a compact, two-axis motor-control PCB built around an ESP32. • Integrate two stepper-motor drivers capable of smooth, quiet motion at plotting speeds. • Provide a reliable USB interface for host control and firmware updates. • Include all required power-management, end-stop, and pen-lifter circuitry so the board can drop straight into an existing Axidraw frame. • Deliver production-ready assets: schematic (PDF & source), PCB layout, Gerber/Drill files, BOM with part numbers, and a brief assembly guide. Firmware scope • Develop firmware that exposes Axidraw-compat...

I need a single-page electrical schematic produced directly in Bluebeam Revu. The goal is a clear, professional wiring layout that I can drop straight into a larger drawing set. i will provide the drawing to modify and excel document with details. On going work. Scope • Draw the complete wiring layout on one sheet. • Work entirely in Bluebeam so I receive the native .bpx file plus a flattened PDF for quick review. Guidelines I don’t have in-house standards for this project, so follow common NEC-compliant drafting conventions and good Revu layer practice. Neat line-weights, legible symbols and a grid that prints cleanly at Arch D are all I require. Deliverables 1. Bluebeam Revu file (.bpx) with editable layers. 2. Flattened PDF ready for print. Once the fir...

I will give you a complete distortion/overdrive guitar-pedal schematic along with a list of the exact parts I want to use. Your job is to recreate that digital circuit in EasyEDA, make sure every symbol and footprint matches the components I provide, and lay out a compact, noise-conscious PCB that can go straight to fabrication. Because this is a digital circuit for an audio pedal, trace placement, ground routing, and jack positioning matter; please keep signal integrity and pedalboard ergonomics in mind while arranging the board. I’m happy with through-hole as long as the parts remain the same ones on my list. Deliverables • EasyEDA project file with the full schematic entered • Optimised PCB layout inside the same project • Generated Gerber/NC drill set ready f...

I am looking for an experienced embedded hardware and audio electronics engineer to replicate a custom automotive audio reverb/DSP module from scratch (0 to 100 delivery). The original circuit uses a Spin Semiconductor SPN1001-FV1 DSP, a Microchip MCP604 quad op-amp, and an external 8-pin EEPROM chip. I need a complete, end-to-end service: hardware reverse engineering, firmware dumping, PCB design, component sourcing, board assembly, and delivery of a fully functional prototype. Scope of Work & Deliverables: 1. EEPROM Firmware Extraction: Extract/dump the binary code from the 8-pin EEPROM chip on the provided reference board to preserve the custom reverb algorithm. 2. Schematic Capture & PCB Design: Recreate the schematic in EDA software (preferably KiCad or Altium) including the...

I'm seeking a skilled PCB designer to create a board for mass production that integrates an ESP32 C3 Supermini with an HLK-LD2410C for sensor integration, specifically a presence sensor. Key Requirements: - Design must facilitate sensor integration - Components: ESP32 C3 Supermini and HLK-LD2410C - Must be suitable for mass production Ideal Skills and Experience: - Proficiency in PCB design software - Experience with ESP32 and sensor integration - Background in designing PCBs for mass production

I need a complete high-frequency RF PCB laid out in KiCad for a signal-processing application. The board must integrate antennas directly on the substrate; no filters or discrete amplifiers are planned at this stage, so every trace, via, and ground return has to be optimized for clean, low-loss feed to the antenna structure. Scope • Translate my existing schematic (KiCad format) into a production-ready multilayer layout. • Model and route all RF paths with controlled impedance, proper stack-up definition, and tight clearance to meet high-frequency performance targets. • Design and tune the on-board antenna geometry, matching network, and keep-out regions inside KiCad’s PCB editor and 3D viewer. • Run DRC, ERC, and any KiCad integrated RF simulation tools ...

I’m building a mobile robot and need an ESP32-based physical hand-held controller that can drive it wirelessly via Wi-Fi or Bluetooth. The only actions the robot must respond to are Forward, Backward, Rotate Left and Rotate Right—no arm control for now. Here’s what I’m looking for: • Clean, well-commented firmware for both the remote unit and the robot side, written in Arduino IDE or ESP-IDF. • A lightweight, low-latency communication routine that keeps the link alive and automatically reconnects if the signal drops. • Pin mapping and a simple wiring diagram for the buttons, power, and any status LEDs you recommend. • Quick setup notes so I can flash the code and verify that each button triggers the correct motion. I’ll consider t...

We are seeking an experienced PCB designer to create a compact, single-board PCB that integrates the following components: - High-precision GNSS receiver IC (u-blox ZED-F9P) - ESP32-S3 Wi-Fi/Bluetooth microcontroller module - 9-axis IMU (Bosch BNO055) - Buck-boost power management circuit for single-cell Li-Ion battery operation - Input protection circuitry (over-voltage, over-current, reverse polarity) - Dual antenna connectivity (SMA and connectors) The board must be production-ready, reliable in field conditions, and designed per industry standards. Deliverables include schematic, PCB layout files, BOM, and Gerber outputs. The designer can use KiCad or EasyEDA as the design tool. Full schematics, pin allocations, firmware interface details, and application context will be shared post...

Job Description We are looking for an experienced hardware/embedded engineer for an upcoming wearable product development project. The product is a compact wrist-worn connected device, and we need someone who has previously taken a wearable or similar battery-powered consumer electronics product from hardware design through prototyping and manufacturing. The device will involve: - Custom PCB / electronics design - Bluetooth Low Energy (BLE) - Microphone + speaker / two-way audio - Low-power embedded firmware - Battery and power optimisation - Wireless charging - Compact wearable enclosure / CAD - Prototype development and testing - DFM and manufacturing handoff The final project will require complete production-ready deliverables including schematics, PCB/Gerber files, BOM, firmware source...

Seeking layout engineer with experience in Altium, low noise analog circuitry, and EMI mitigation. This project encompasses minor updates to an existing board which has already passed EMI testing. There may or may not be a desire to further reduce emissions, but the main focus is signal processing updates.

I’m putting together a simple proof-of-concept: an XY plotter that uses stepper motors and a motor-driven cream / syringe head to write one predefined word on plain paper in four different sizes. The word and the sizes will be hard-coded for now; no live UI or font selection is needed. I just want to see smooth, accurate motion, clean cream extrusion, and clearly legible lettering in an “Elegant” style. Here’s what I need from you: • Mechanical design and parts list for the XY frame, rails, carriage, and syringe mount, all sized for an A4 sheet of paper. • Electronics schematic and firmware (Arduino + GRBL, or any open-source control stack you prefer) that drives two XY stepper motors plus a third actuator for the syringe. • G-code or equivalen...

I need an expert to test and fix circuit components for a radio project. Key tasks include: - Tasting and fixing circuits on both breadboard and PCB - Primarily focusing on transistors and diodes - Diagnosing and resolving short circuits Ideal Skills and Experience: - Proficiency in working with transistors and diodes - Experience with both breadboard and PCB setups - Strong troubleshooting skills for short circuits Looking forward to your bids!

I have a working surface-EMG biofeedback prototype that is almost ready for a clinical trial. My background is in Occupational Therapy, so I need a technically-minded partner to finish the engineering details. The prototype already captures clean EMG signals, but three areas still need work before it enters the clinic: 1. Fixing the vibration sensor • Diagnose the current instability (occasional dropouts and inconsistent amplitude) • Re-calibrate and, if necessary, replace the sensor so it triggers haptic feedback within 50 ms of threshold detection • Deliver updated firmware and wiring diagram 2. Building EMG display software for Windows • Real-time data visualization (raw signal and RMS/average) • Session recording to CSV or similar fo...

I’m looking for an experienced MCC electrical engineer to prepare fully detailed control-panel layouts for a new motor control center I’m building. The scope is strictly design and drafting, so no field installation or troubleshooting is involved. The drawings must be produced to recognised industry benchmarks—UL508A and IEC 61439—and be ready for direct hand-off to our fabricator. I’m happy for you to work in AutoCAD Electrical, EPLAN, or a comparable CAD platform as long as the native files and PDFs are delivered. Deliverables • Scaled control-panel layout drawings, showing component placement, wireway, and clearances • All supporting schematic pages referenced by the layouts • Bill of materials tagged to each drawing • Final ...

I’m ready to commission the complete electronic design for a 150-300 W pure-sine-wave solar inverter that will run from a 12.8 V / 100 Ah LiFePO4 pack and deliver 220 VAC. The unit must operate reliably indoors and outdoors, fit comfortably within a 10 × 20 cm footprint, and meet commercial-grade durability standards. Core electrical requirements • True sine-wave topology with ≥90 % efficiency under typical load • Clean 220 VAC output, THD ≤3 % at 150 W, full-power capability to 300 W • Input 12 VDC nominal, LiFePO4 profile charging via high-frequency PWM • Integrated SoC display or LEDs for real-time battery percentage and charge status Protection & safety Over-temperature shutdown, overload limiting, and fast-acting short-circuit prot...

We are looking for an experienced RF PCB Layout Engineer to review and complete an existing multi-radio PCB design. This is not a design-from-scratch project. The schematic, component placement and most signal/power routing are already completed. The remaining work is focused mainly on RF layout finalization and production-readiness review. Required experience: Sub-GHz / LoRa RF PCB routing LTE RF layout GNSS RF layout 50-ohm controlled-impedance routing RF matching networks antenna feed layout ground return and stitching-via strategy RF keep-outs and isolation multilayer PCB stack-up EMI/EMC-aware layout KiCad The selected engineer will be required to review the existing PCB, complete/correct the RF sections and bring the board to fabrication-ready status. Expected deliverables incl...

We are looking for an experienced Automotive Electronics / PCB Design Engineer to modify and extend an existing vehicle tracking hardware design into an OBD-II telematics device. The project will include two variants: Modern vehicles – OBD-II with CAN communication. Older vehicles – OBD-II with CAN + K-Line support. We prefer a common hardware platform where possible, with different BOM/configuration options for the two variants. The engineer must have proven experience with OBD-II, CAN Bus, K-Line, automotive power supply/protection, PCB schematic design, and vehicle telematics hardware. Initial deliverables will include the updated schematic, BOM, component selection/alternatives, interface design, automotive protection circuitry, and design documentation. IMPORTANT: Th...

I have an NXP 595-based concept that has to fit into an 18 mm footprint and be reproduced on twelve identical boards. The boards are for development and testing, yet I need production-grade documentation so I can send the files straight to fabrication and assembly without extra rework. Core requirements • High-integration layout that combines power management, signal processing and data communication on the same tiny PCB • Clean, EMI-conscious routing to keep signals reliable despite the tight real estate • All design files delivered in a mainstream ECAD package (Altium Designer, KiCad or similar) along with manufacturing outputs Deliverables 1. Complete schematic with component libraries 2. PCB layout and 3D step model in the agreed tool 3. Gerber and drill fi...

I need a small 33 x 29 mm membrane touch latching switch printed circuit board (PCB) with only 8 SMDs on it, copied for a obsolete device. I'm looking to get 100 of these made, possibly 200 depending on pricing. I can send the 6 component list and photos of the circuit board and a complete circuit board is this 2 sided. The active devices are a ATMEL TINY 13A (needs programming and a PA1CD (i think it's a zener diode, 4 resistors and 1 capacitor. On the decal side there is a small led that lights when latched. It needs to be copied exactly because this switch circuit gets glued into a recess in a plastic case with cutouts for the components so the board lays flat. I may not need the switch decal. Run on a 3.7VDC battery. Key Requirements: - Exact replication of the existing PCB...

I have a consumer-electronics project that is almost ready for production, but I need a fresh set of expert eyes before I commit to tooling. Your job is to scrutinise every level of the design and give me a concise, actionable report. Scope of the review • Schematic – confirm AC isolation, creepage distances, relay selection and power-supply safety. • PCB layout – check placement, clearances, return paths and routing discipline. • BOM – verify component availability, footprints, part compatibility and RoHS compliance. • Firmware – validate logic for sensors, alarms, GSM SMS/call handling, relay control and fail-safe behaviour. • Safety & compliance – highlight anything that could jeopardise CE (LVD/EMC) readiness and fla...

I’m leading a senior-year project where my student team will build and test an induction-motor drive (motor, VFD, sensors, protection, filters, the works). What we’re missing is seasoned electrical-engineering insight during the DESIGN phase. Here’s what I’d like from you: • Review and refine our single-line and wiring diagrams, ensuring safe operation on a 3-phase, 480 V supply. • Help size and specify the motor, VFD, fuses/MCB, contactors, braking resistor, EMI/RFI filters, current/voltage sensors, and any surge- or overload-protection devices. • Validate thermal calculations, harmonic considerations and grounding/shielding practices. • Provide a concise Bill of Materials with part numbers and vendor suggestions, flagging long-lead or co...

I have a consumer-electronics concept ready for the next step and need a clean, production-ready double-layer PCB layout. The board will host a mix of through-hole and surface-mount parts, so component placement and routing must accommodate both styles without ballooning the footprint. Deliverables: • Finished design files in Altium and industry-standard Gerbers • Drill files, pick-and-place data, and a tidy BOM (Excel or CSV) • Test PCB's with assembly I will review the Gerbers in ViewMate and run a quick fit-check in our enclosure CAD; the project is complete once the files import cleanly and the report answers all open questions. Looking for someone in India, Delhi NCR Region. Thanks

I’m developing a dedicated handheld that will operate offline. No Wi-Fi, Bluetooth, cellular, or any other radio is required, so the entire design has to function in isolation. Because of that restriction I’m open to whichever operating system keeps the footprint light and the boot time quick, whether that’s a stripped-down Android build with networking stacks removed or a fully custom OS. but more likely just on/off. then a button to run. Your task is to take the idea from concept to a working prototype. I’ll need the electronic design (schematic, PCB layout, and component selection), a daylight-readable display, a rechargeable battery able to power at least eight hours of continuous use.. Low power consumption, immediate on/off and rock-solid stability. Delivera...

I already have a universal BLDC ceiling-fan driver PCB running perfectly from mains power; what it lacks is an Arduino brain. My goal is to plug an Arduino (Uno, Nano, or whichever you prefer) into the existing driver so I can: • adjust fan speed across its full range, • reverse the direction on command, and • set on/off timers, all through a small set of physical push-buttons mounted near the fan. What I need from you is a clean, well-commented sketch plus a minimal wiring diagram that shows exactly where every button, resistor, and logic-level signal ties into the driver board. If any level-shifting, opto-isolation, or triac/FET gating is required, please spell that out and include the component values. Debounced button handling and non-blocking timer logic (e.g., u...

I’m building a proof-of-concept noise-reduction module destined for consumer-grade electronics. My priority is an electronic schematic that delivers two core capabilities: active noise cancellation and echo reduction. The circuit must be small enough to embed in another typical product that will be mentioned later on as the project develops. Here’s the flow I have in mind. First, we collaborate on the signal-processing topology—feed-forward, feedback, or hybrid—then translate it into a detailed schematic and PCB layout (Altium, KiCad, or your preferred EDA). Once the draft design is ready, I’ll need simulations or bench measurements that prove at least 20 dB attenuation in the 50 Hz–2 kHz band while holding latency under 10 ms; please include SPICE plot...

Industrial 220V Power Supply & Machine ON/OFF Control PCB Design I am looking for an experienced Power Electronics / PCB Design Engineer to design a compact industrial power supply and control circuit that will work with our existing IoT device. Main Requirements - Input: 220–240V AC industrial supply - Provide stable DC power to our existing IoT device - IoT device will provide the control signal for Machine ON/OFF - Circuit must safely switch/control the industrial machine using an appropriate relay/contactor/SSR or other suitable solution - The machine load current will pass through or be controlled by the designed switching section - Proper isolation between high-voltage AC and low-voltage IoT electronics - Include necessary protection: fuse, surge protection, over-current...

I’m putting together a compact dual-camera dashcam that can watch the road and simultaneously monitor the driver. I already have the product vision and feature set defined; now I need an embedded systems specialist who can turn it into working hardware and firmware. Core functionality • Two SD-resolution image sensors, one road-facing and one cabin-facing • Live video uplink over 4G/LTE plus on-device recording to a removable SD card • GPS receiver for continuous tracking and metadata stamping • Integrated motion sensing and true impact detection, so an on-board accelerometer must trigger and flag critical events even when the car is parked • Clean vehicle-grade power input and automatic power-down logic to protect the battery Scope of work 1. Com...

I need a complete set of EPLAN schematics that map out the electrical drivetrain of my vehicle prototype. The focus is strictly on the electric motor and its controller; auxiliary items such as battery packs, charging modules, or transmission layouts are outside this job’s scope for now. You are free to work without binding standards, so feel comfortable applying your own best-practice symbols, macros, and page templates in EPLAN Electric P8. What matters most is clarity, consistent device tagging, and tidy routing so my in-house engineers can drop your file straight into the broader vehicle project. Deliverables • Native EPLAN project file (.elk / .zw1) with all pages clearly labeled • PDF export for quick review • Simple parts list (motor, controller, core co...

We are Safe Instrumentación (Bogotá, Colombia). We design a modular data-acquisition system for geotechnical and industrial instrumentation, with four boards: a main "Brain" (STM32G0B1RE, FRAM, LoRa, LTE modem, RS-485, native USB) and three accessory nodes (vibrating-wire VM501C, inclination SCL3400, and a DS18B20 temperature chain of up to 200 sensors). We already have a working prototype. We do NOT need firmware — we develop it ourselves. We need a senior engineer (or firm) to take the hardware to production: Review and optimize the existing schematics Verify and strengthen protections (ESD, surge, EFT; galvanic isolation on RS-485; reverse-polarity/overcurrent) Optimize power management and consumption (seamless mains/battery switching, low-power modes, l...

I’m building a small consumer-electronics project and need a purpose-built, rectangular PCB that can drive an induction heater at up to 100 W. The board must accept power from either a standard DC adapter or a USB-C PD or DC source, automatically negotiating or routing whichever is connected. Power control is intentionally simple: ten individual LEDs indicate output in 10 W increments (10 W – 100 W), and a single rotary dial steps the power up or down in those same 10 W stages. No screen, menus, or extras—just clean, reliable hardware. What I expect from you • Complete schematic with component values, coil connection, gate-drive stage, protection (over-current / over-temp), and USB-C PD or DC supply trigger circuitry. • PCB layout ready for fabrication...

I’m moving an industrial project from concept into detailed engineering and need a seasoned electrical designer to pick up the load calculations, schematics, and layout work. The scope centres on two areas: • Power distribution systems – accurate single-line diagrams, cable sizing, panel schedules, short-circuit and voltage-drop studies. • Control systems – control panel layouts, I/O lists, and wiring diagrams that integrate smoothly with PLC hardware. I already have general corporate guidelines and typical drawings that outline preferred symbols, layer naming, and drafting conventions; you’ll refine and expand these into full construction-ready documents that comply with NEC/IEC and any site standards we identify together. Typical deliverables I&rs...

I need a qualified electrician for testing at a solar farm. Requirements: - Use testing equipment (provided + training if required). Ideal Skills and Experience: - Level 3 electrical install - Level 3 testing - CSCS or ECS card

We are looking for an experienced Mechanical/CAD Designer to design our custom filament 3D printer, GenZ OG. Main Requirements: CoreXY printer Build volume: 200 × 200 × 200 mm Unique modern design, not a standard box shape Complete 3D CAD assembly Frame, toolhead, heated bed and belt-system design Component selection and BOM Manufacturing drawings STEP, STL, DXF and editable CAD files Support for minor corrections during prototype assembly The candidate should have experience designing 3D printers, CNC machines, robotics or similar mechanical products. SolidWorks or Fusion 360 experience is preferred. Please share your relevant portfolio, availability, timeline and final quotation.

I am looking for an electrical engineer / KNX specialist to prepare the complete execution documentation for a residential KNX/DALI installation. The installation itself will be carried out by a local electrician in Switzerland based on the plans and documentation we finalize together. The required scope is divided into three phases: Phase 1 – Design and Planning * Review the architectural plans and requirements * Review and finalize the electrical, KNX and DALI design * Finalize fuse box layout, protection devices and component locations * Finalize conduit and cable planning Phase 2 – Detailed Documentation * Prepare complete fuse box drawings * Prepare detailed 230 V, KNX, DALI and low-voltage wiring diagrams * Prepare conduit and cable schedules showing cable types, size...

I need assistance with optimizing and designing a PCB for a water treatment system. I have all the necessary components, including: - TDS sensors - Pressure sensors - Flow sensors - Relays - Float switch - Solenoid valve The ideal freelancer should have experience in: - PCB design - Component optimization - Working with water treatment systems Please provide a printable PCB design for the finished product.

Project Overview: We have a completed engineering design, schematics, and a preliminary Bill of Materials (BOM), along with a 3D STEP mechanical model for a portable electronic thermal device. We are looking for an expert PCB design engineer to prepare and deliver a complete Manufacturing Package ready for immediate submission to major PCB manufacturers (such as PCBWay / JLCPCB) without any errors. Main Tasks & Deliverables: Review the design and BOM, and propose the optimal PCB technical specifications (such as copper thickness, FR-4 TG thermal rating, and surface finish) based on the device's power and heating circuitry requirements. Gerber Files: Standard RS-274X format for all layers. Excellon Drill Files: Accurate drill and hole specifications. Pick-and-Place / CPL File:...

This project takes a brand-new consumer-electronics board from concept all the way to files the factory can put straight on the pick-and-place line. The design is SMT-only and must integrate an on-board Wi-Fi/Bluetooth module, so careful RF layout, impedance-controlled routing and a compact, cost-optimised stack-up are essential. I will share a functional block diagram, mechanical limits and the key IC selections; you translate that information into production-ready hardware. Throughout the process I expect clear, well-documented design files that make future revisions simple. Deliverables • Editable schematic with clear net-naming and annotation • PCB layout observing DFM/DFT rules and vendor constraints • Manufacturing outputs: Gerbers, drill, pick-and-place and ce...

Taşınabilir bir kontrolcü tasarlıyorum; ESP32, ekran ve joystick gibi tüm bileşenler elimde fakat ekranın ESP32’ye doğru şekilde bağlanması ve çalıştırılması için desteğe ihtiyacım var. Öncelikli hedefim: • Ekranın ESP32’ye hatasız fiziksel bağlantısı (pin planı, güç hatları, arka ışık kontrolü). • Uygun sürücü kütüphanesini (örn. TFT_eSPI, LCD, OLED vb.) yapılandırıp örnek kodla görüntü alabilmek. • Joystick okuma kodunu ekranda canlı gösterecek basit bir demo hazırlamak (isteğe bağlı, zaman elverirse). Benden beklenen çıktı: 1. Kısa sürede uygulanabilir bağlantı şeması (KiCad, Fritzing veya PDF). 2. Çalışır örnek kaynak ko...