Dual ESP-32-PCB with 6-IRQ, 4 stepper motors, 1-ADS1256, USB_SD, nRF24
Budget $30-250 USD
Job Description:
Dual ESP-32-PCB with 6-IRQ, 4 stepper motors, 1-ADS1256, USB_SD, nRF24
PCB BRD with
1. Size 190mm by 1mm or less with 1 side 140mm min and 140 by 10mm not used (Blanc), this strip is used to be plug in the sockets for holding.
Design OPAL PCB using 2 ESP32 processors
1 ESP32-Master
1. nRF24 –2pins(SPI)
2. SPI-3pins
3. SD_USB-0pins(con to Data_TX duplicate)
4. ADC1256-24bit-2pins(SPI)
5. 4-IRQ-Fast(1000HZ)-Opto-4pin
6. 3 UART-TX/RX -6pins
7. 4 single lines on Opto -4 pins
8. Total =2+3+2+4+6+4=21pins
1 ESP32-second
1. //nRF24 –2pins(SPI)-0pins
2. SPI-3pins
3. //SD_USB-2pins-0pins
4. Can be on board A/D // ADC24-2pins(SPI)
5. 4-IRQ-Slow (200HZ)on OPTO-4pin
6. 2 UART-TX/RX -4pins
7. 4 St-Motors =12pins
Total= 3+2+4+4+12=25pins
Awarded to:
27 freelancers are bidding on average $162 for this job
Best ESP32 Design Expert at your doorstep! Dear Client, We have lots of experience in ESP32 so we able to do this project for you. We can provide Dual ESP-32-PCB with 6-IRQ, 4 stepper motors, 1-ADS1256, USB_SD, nRF24 More
Hi there, I have read your project description and i'm confident i can do this project for you perfectly.I still have a few questions. please leave a message on my chat so we can discuss the budget and deadline of the More
Hi Client. I have many experiences working for 12+ years with Circuit and PCB design. and I have ever design the PCB project using esp32, nrf24, motor driver, etc. I am sure I can complete your project perfectly. If yo More
Dear Client. I have just read your job description and your project is really interesting to me. I have many experiences working for 12+ years with Circuit design, PCB design, manufacturing functional prototyping with More
FREE OF COST CONSULTATION Dear Client, I am a Professional PCB Designer so I can design Dual OPAL PCB Design based on ESP32 with 6-IRQ, 4 stepper motors, 1-ADS1256, USB_SD, nRF24, 25 pins while meeting all requirements More
Hello... You want Pcb design for custom ESP32 layout. My Introduction: I have master degree in Mechatronics Engineering, have 7 years of Industrial experience in dealing with Power Electronics, Electrical Engineering, More
Hi I'm very glad to have an opportunity to help you with PCB design. This job is very appealing to me because I have a lot of experience in circuit and PCB design with ESP32 WROOM and WROVER module. I'll be very happy More
Hi, We can make the Dual ESP-32-PCB with 6-IRQ, 4 stepper motors, 1-ADS1256, USB_SD & nRF24. I came across with your requirement very carefully. We have specialization in PCB designing from last 20 years. Here is our More
I am a BSc Electrical and Electronics Engineer with a specialization in Power & Control Engineering, and an MSc Telecommunications Engineer with a specialization in Electronics. I have 5 years of experience in the fiel More
Hi! I have understood your requirnments about your project with every detail of it. I am an Electrical Engineer with more then 9 years experience in electronics, circuit design, PCB layout, Verilog, FPGA, Embadded Syst More
Hi I read your complete description and i understand what you want I am an electrical engineer with experience in pcb design Thanks
Dear sir, iam ready to keen work with you.I have 13 years of exp in pcb design. Hands exp on HDI designs. Regards. Shrishail.
I am an electronic engineer with solid hardware skills and recognized experience in the design of electronic boards I can do ur job as well Thank you!
