EEPROM simulation for STM32F407VGT6 mictocontroller

Hi, I am an Embedded System Developer and have an 7 years of industrial experience. I have done lots of project in keil uVision, OpenStm32,Truestudio,IAR Embedded Workbench, Code Composer Studio (CCS) using Embedded C/C++. I have used almost all kind of ARM Cortex M0 - M4 based Microcontrollers like Stm32,LPC148,Tiva TI tm4C123,stm32f4xx,etc.. So this task is very easy for me to complete. I will assure you that if you work with me you will have a quality code and on time completion. Kindly contact me as soon as possible to discuss further. Looking forward for a positive response.

Good Day I have written and built embedded firmware for Jigs requiring self calibration using EEPROM stored values on start up. I will be pleased to assist in reading the existing code and adding your three Variables. Regards Future

hello there , I have experience using this same board (the STM32f407), also I have it so we can test the project on hardware. I have experience with embedded systems in general for 2 years and I have worked with different microcontrollers such as ATMEGA32 , pic16f877a, STM32f407 and tm4c123g looking forward to working with you.

Hi, I am embedded engineering with more than 5 years of experience in embedded. I work with different controllers and sensors. I have already work with STM32F series and EEPROM programming. So, I am sure that I am able to help you with my past experience. I am looking forward to work with you and to discuss about project. Thanks, Rahul

Hi, I'm a professional embedded firmware developer and have 4+ years of experience. I've worked on Keil ide and I'm sure I can fix your issue. You can pay me only after I completely deliver your project.

I have experience in eeprom . I can help you . I am embedded software engineer . Now I am IoT expert.

I had experience in Stm32 non volatile memory like Eeprom using I2C bus, or Flash Memory using SPI bus. I had strong confidence that can finish your task on time.

Hi, Greetings I have the solution to your problem of "variable data should not get erased after power down". Let me tell you about the solution in PM and start implementing it with STM32F407VGT6. Thanks and Regards Sourav Sharma

Hello, I have a code already tried and tested for the STM32F0 series. All I have to do is port it to your controller. Also, if you want your code to run, I can do that too. I know everything about emulated EEPROM of STM32.

Proven 3.9 years of experience in developing embedded products from scratch. In one of my customer product handled the same requirement where they want to store & update configuration. I can handle your requirement. Looking forward to hear from you. Thank you.

I already use stm32f4 with EEPROM to save multiple collections data from input devices. So i can help you to acheive your target.

I have interfaced the EEPROM with ST microcontrolers.I have gone through your description and have two doubts to clarify. 1) which EEPROM are you using 2)which library are you using for STM32.(HAL or LL).

I'm Electronic engineer, My electronic design exprience since 2009 from Medical Breathing Device Manufacturer in TURKEY ! Over the 9 year ı used at my design Atmega series microcontrollers and ARM base STM32 group M0 to M4 class microcontrollers. Generally ı designed; Sensor controller electronics (Pressure control, flow control, Gas level and ratio control circuit and also dc motor control systems.) and valve or motor drive circuits. I'm using c and c++ with CubeMX IDE to developped my microcontroller software. For designing my circuit schematic and PCB drawings i'm using to Kicad. I can draw 4 or 6 layer PCB with Kicad.

i'm Embedded Systems software developer Technical Skills: • C Programming • Tools: Eclipse, Proteus. • Platforms: Aduino , AVR atmega32 , ARM STM32F103. • Peripherals: GPIO, ADC, Timers, PWM, ICU, Interrupts. • Protocols: UART, SPI, IIC. • Hardware: PCB design. Trainings: • Information Technology Institute ( ITI ) Embedded Systems Track - Embedded Systems software development, building drivers for peripherals and communication protocols, building layers MCAL, HAL and LIB ... etc

Hello, I am a passionate embedded C programmer with 10 years experience in the domain. I have worked on ARM core for many of my projects. I will deliver quality work product meeting your timelines. Let me know if you find my profile suitable for your requirement. Regards, Parvathi