Looking for Embedded Software Engineers

Dear Client I am excited to submit this proposal. I have rich experience over than 10 years in the embedded system. I have developed a lot of the products during past 10 years I think I can help you on your project. I'll look forward to your reply. Best regards.

Hi, I am Electrical and Electronics Engineer with 14 years experience in micro controller programming. Microcontroller : Arduino, ATMEL, PIC, AVR, raspberry Pi, ESP8266, ESP32 ,NXP, SiLabs Regards Senthil Chennai,India

I have electronics and telecommunications. I have over 15 years of experience programming AT89Cxx, AVR. I am very good at electronic components: Pmosfet, transistor, DIODE Switching, CD40xx, Opamp, HFE, 74hcxx.. ec Recently I have 4 years of arduino programming experience: ESP32, ESP8266, Key I.T Skills ● Programming: High level Assempler, languages like assembler (MIPS and X86) AVR, AT89xx, VB6, Assembler, Pascal, C ● Software : MS Office, Adobe illustrator, Orcad Key Competencies ● Design Power inverter. ● Design interface: RJ45, COM, IC2, USART, SPI, SD card. ● Components device: Analog, Digital, Filter, Microcontroller, RAM, Sensor, ADC, DAC. ● Set up computer networking. Configure computer hard and software for automation purpose. ● Remote control by computer. Engineering Electronics Electrical Engineering PCB Layout Circuit Design Can you give me a programming project on avr, arduino, ESP32, tft..ec You can also assign me to design both hardware and firmware. To test my ability to meet the needs of the work with you thank you

Hi, I am kahan, I am embedded developer and have much experineced in hardware and software side. Waiting for further conversation. Thank you.

please discuss .........................................................................................................................................................

Have expertise in Arduino projects. If required we can have some telephonic discussion about my expertise on Embedded C.

I have an engineer diploma in electronics and embedded system, I interested your project description. I'm an experience in electronic design and embedded system: Protocol: I2C, UART, BUS, SPI Embedded system based on Microcontroller (ATMEGA, AVR, STM32, PIC, Arduino...) and programming firmware C/C++, VHDL, python and software Qt, GUI. PCB layout designing, providing GERBER, 3D files using Altium.

Dear Sir/Madam: I am Electrical Engineer, many years of Firmware development, circuit design, PCB design experience. I have used different boards, Arduino, STM32, Raspberry PI, BeagleBone, DSP etc. I have used Altium Designer for many years, designed many PCBs, single layer, multi layers, RF circuit, Bluetooth, Wi-Fi, Microcontroller etc.… This includes schematic capture. I can perform circuit simulation and confirm functionality. I have used various IDE software, Arduino IDE, IAR workbench, Keil etc. I have designed our own BLE module using the nRF51822. This was designed for iBeacon functionality. The module is small and uses CR2032 battery. I have experience with GSM GPRS modems. I have a working SIM808 GSM GPRS system, which uses STM32 to send AT command to the modem. I have written code for this and created hardware PCB design. I have tested this with Vodafone and Airtel networks in Mumbai. The work performed is guaranteed. Please contact me and we can discuss the project. Thank you Sincerely, Jatin Mehta

I'm an italian electronic engineer with more than 15 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC, ARM Cortex, ESP32) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Eclipse + GNU ARM GCC for different ARM Cortex M0/M0+/M3/M4/M33 manufacturers (STM32Fx, NXP, EFM32/EFR32 SiLabs, Nordic nFR5x, but I'm ready to learn new frameworks). I have also good experience with ESP32 in "esp-idf" framework. I work with both single task (bare metal) and multi task environment (FreeRTOS, RTX,...). I write code for low level driver (GPIO, UART, SPI, I2C, PWM....) management, for medium level (driver for sensor, MEMS, memories, fuel gauge, display,...) and for high level/final application, for bootloader and for OTA. I work also in "C code" commercial boards Arduino/Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. All my code is covered by unit/integration/stress tests.

Hi Sir i have total 14 years experience in embedded firmware development using C,C++,Assembly languages. I have worked on Controllers like PIC, TI Piccolo C2000 DSP controllers, MSP430,Infineon XMC series.I have developed firmware for power systems like DC DC , AC DC, Solar Charge controllers ,Inverters and data wired communication protocols like USART,I2C,SPI,CAN ,MODBUS RTU. I can work on this task ,please let me know if you have questions.

Am a Embedded Engineer with 3yrs of total experience. Achievements are submitted project concepts to govt of Telangana. Can do Embedded System Design, Embedded Product Development Hardware and Software. Hands on Experience on Arduino, Raspberry Pi, STM32, NodeMCU Microcontrollers. Hands on Experience on all Embedded Protocols.

I have 3 year experience in embedded systems and iot. I have done project related to rpi3b+, rpi4, esp32, arduino uno, arduino mega, due, nodemcu. please also check my potfolio. I am familiar with linux debian, python language and c embedded.

Hello, I am embedded engineer from Mumbai, India. I have 2+ years of experience in embedded field. I have worked on several microcontroller including PIC. I have programming experience in embedded c and MATLAB. I have used PROTEUS, ORCAD for circuit schematic design and PCB layout. I have used multiple IDEs like KEIL, Kinetis design Studio, MPLAB etc. I am looking to provide better service and will deliver as per deadline.

Hi, I am a experienced Embedded professional living in Delhi. Please see my profile and portfolio ,send a message if you find it suitable. Regards, Avinash